Writing · How-to
How to prepare images for Spectra 6 e-paper signs
To prepare an image for a Spectra 6 e-paper sign, crop it to the panel's exact native resolution, design with the six real pigment colors (black, white, red, yellow, blue, green), choose a dither that suits the content, and approve the dithered preview rather than the source file. Flat color and big type look printed; gradients and photos become a fine grain.
Published 2026-11-12. Written for the designers and merch teams who make artwork for color e-paper signs. The resolutions, pigment values and dither choices below come from the image pipeline we ship with our own ESP32-S3 + Spectra 6 hardware.
Why e-paper artwork is different
A Spectra 6 panel does not mix light like a screen. Each pixel is one of six physical pigments. Anything else the eye sees, from orange to skin tones to gray, is a pattern of those six placed next to each other, which is what dithering does. The pigments are also reflective, so the panel is only as bright as the room, and they cannot reach the saturation of a backlit monitor. The maintainers of epdoptimize, an open-source e-paper dithering library, make the same point: panels cannot cover the full sRGB color space, so dithering has to use calibrated colors rather than ideal ones.
The practical result: artwork approved on a laptop screen will look different on the wall. The steps below close most of that gap before anything reaches a sign.
Step 1: Crop to the panel’s native resolution
| Panel | Size | Native pixels | Rough paper size |
|---|---|---|---|
| Good Display GDEP073E01 | 7.3″ | 800 × 480 (landscape) | About A5 |
| Good Display GDEP133C02 | 13.3″ | 1600 × 1200; we handle it as 1200 × 1600 portrait | About A3 |
Design at exactly those pixels, or crop to them before dithering. Dithering creates a pixel-level pattern; if the image is resized afterwards, the pattern turns to mush. Our CMS puts a crop step in front of every upload (pan, zoom, rotate to the exact frame) and only dithers once the crop is fixed. The byte buffer it sends to the sign is validated against the panel’s exact size, so an image at the wrong resolution is rejected rather than stretched.
Decide orientation per placement. A shelf-adjacent card is often landscape; an endcap or door sign is usually portrait. Making one master in each orientation is cheaper than cropping a landscape campaign into portrait at the last minute.
Step 2: Design with the six real pigments
The values below are the measured pigment colors in our optimizer’s default Spectra 6 profile. They are what the panel actually reflects, not the pure RGB values a design tool offers. Put them in your design file as swatches.
| Pigment | Measured RGB | Use it for |
|---|---|---|
| Black | 12, 12, 12 | Body text, outlines, logos. The most reliable pigment for small detail. |
| White | 243, 241, 237 | Backgrounds. An off-white, so pure #FFFFFF in a mockup will not match. |
| Red | 192, 56, 44 | Prices in promo art, alerts, brand reds. Reads as brick red, not screen red. |
| Yellow | 217, 188, 49 | Highlights and badges. Weak as text on white; put it behind black type. |
| Green | 63, 146, 87 | Status, fresh or eco cues, wayfinding. |
| Blue | 58, 98, 185 | Brand blues, wayfinding, calm backgrounds behind white or black type. |
The rule of thumb: Areas filled with one of the six pigments render solid, like print. Areas in any other color render as a dot pattern of two or more pigments. Put brand marks, headlines and prices on solid pigments; let photos and illustrations carry the dithered colors.
If your brand color is not close to one of the six, decide up front whether a dithered version is acceptable or whether the sign uses the nearest pigment. Brand teams tend to accept a slightly different red more easily than a grainy one.
Step 3: Pick the dither for the content
Not every image wants the same treatment. Our Python optimizer classifies the content and offers four presets:
| Content | Dither | What it does |
|---|---|---|
| Photos, portraits, natural scenes | Stucki (error diffusion) | Smooth gradients, natural skin |
| Bold posters, high-contrast graphics | Bayer (ordered) | Regular pattern, stronger color, sharp edges |
| Line art, comics, flat fills | Atkinson (error diffusion) | Crisp lines, clean flat areas |
| Text, UI, dashboards | None | Nearest pigment only, sharpest text |
For everyday uploads, our browser pipeline uses one default: Atkinson error diffusion, nearest color against the panel palette, and no saturation, contrast or brightness adjustment. In our own side-by-side preference testing across hundreds of images, that neutral setup was preferred over versions with tone boosts. Boosting saturation can still help a specific poster; do it to the artwork on purpose rather than to every image by default.
Step 4: Set type for a reflective panel
- Keep text on solid pigment. Black on white, white on blue, black on yellow. Text over a dithered photo breaks up.
- Go bigger and bolder than print. Thin strokes and hairlines can fall between pixels. Check legibility at the real viewing distance, not zoomed in.
- Render text without dithering. If the sign is mostly text, such as a room sign or a status board, use the no-dither path so letter edges stay clean.
- Avoid yellow text on white. The contrast is low on screen and lower on paper-like pigments.
Step 5: Approve the dithered preview, not the source
The person signing off should see what the panel will show. Our CMS dithers in the browser before upload, so the preview on screen is the exact pixel pattern the sign will draw; the original file never needs to leave the designer’s machine. Even so, a monitor is brighter than a reflective panel, so for a new campaign put one real sign under the store or office lighting before the rollout.
Plan around the refresh too. A full Spectra 6 color refresh takes roughly 20–30 seconds and the panel flashes while it changes. Our firmware also runs an occasional clear cycle to remove ghosting, which looks like a slightly longer refresh. Schedule swaps for opening time or quiet hours. The holiday promo checklist shows how we time a seasonal changeover.
Pre-flight checklist for every campaign
- Artwork made at the panel's native resolution, one master per orientation
- Six pigment swatches in the design file; brand marks and headlines on solid pigment
- Prices left off brand promo signs unless they come from the same source as the till
- Text on solid backgrounds, sized for the real viewing distance
- Dither chosen for the content: photo, poster, line art or text
- Dithered preview approved by the person who owns the brand
- One real sign checked under the actual lighting before rollout
- Swap scheduled outside peak hours, allowing for the 20 to 30 s refresh
- Old campaign art removed from the schedule so it cannot come back
Related reading
Firmware teams can find the dithering and waveform side of this in our ESP32-S3 + Spectra 6 field guide. If you are still choosing a display, the Spectra 6 vs Kaleido 3, Gallery 3 and BWRY comparison covers color quality and refresh, and color e-paper for brand shelves and endcaps shows where this artwork ends up.
FAQ
What resolution should images be for a Spectra 6 display?
Exactly the panel’s native resolution. The 7.3-inch GDEP073E01 is 800 × 480 and the 13.3-inch GDEP133C02 is 1600 × 1200, which our pipeline handles as 1200 × 1600 portrait. Crop to that size before dithering so the dither pattern is not scaled afterwards.
What colors can a Spectra 6 panel show?
Six pigments: black, white, red, yellow, blue and green. Every other color, including orange, pink, brown, skin tones and grays, is made by dithering a pattern of those six. The real pigments are less saturated than pure screen RGB; white is an off-white and red is a brick red.
Which dithering algorithm is best for Spectra 6?
It depends on the content. Our optimizer uses Stucki for photos, ordered Bayer for bold posters, Atkinson for line art and flat fills, and no dithering for text and dashboards. For general uploads our browser pipeline uses plain Atkinson with no tone adjustment, which ranked first in our own side-by-side preference testing.
Why do my images look washed out on color e-paper?
Because e-paper is reflective and its pigments cannot cover the full sRGB range. An image proofed on a backlit monitor will always look brighter there. Design with colors close to the six pigments, approve the dithered preview rather than the source file, and look at a real panel under the lighting where it will hang.
Can I put photos on a Spectra 6 sign?
Yes, with dithering, and they look good at viewing distance with a visible grain up close. Spectra 6 is at its best with illustration, brand marks and flat color. If photographic fidelity is the reason for the sign, use an LCD or OLED instead.