Writing · Comparison
7.3-inch vs 13.3-inch color e-paper: choosing a size for a sign or product
Choose 7.3-inch color e-paper for signs read up close and changed often: door and desk signs, shelf and counter signs, labels. Choose 13.3-inch when the sign has to carry a whole timetable, floor plan or poster, or be read from across a room. Both use the same six-color Spectra 6 film and refresh in tens of seconds; the 13.3-inch has about five times the pixels, needs PSRAM on an ESP32, downloads a 960 KB image on every change and costs three to four times as much as a bare panel. We ship both sizes on the same firmware, and the table below is from our own builds plus the published specs we could check.
Published 2026-11-20. Written for product teams and operations leads choosing a panel size for a sign, label or frame. Our reference hardware is ESP32-S3 with Good Display’s 7.3-inch GDEP073E01 and 13.3-inch GDEP133C02 Spectra 6 panels; figures marked as ours come from that firmware. Other figures link to the page we read them on.
7.3 vs 13.3 inch at a glance
| 7.3-inch | 13.3-inch | |
|---|---|---|
| Panel on our builds | Good Display GDEP073E01 | Good Display GDEP133C02 |
| Resolution | 800 × 480 | 1600 × 1200 (we drive it 1200 × 1600, portrait) |
| Pixel density and shape | About 127 PPI, 5:3 | About 150 PPI, 4:3 |
| Active area | About 160 × 96 mm (derived from pixels and PPI) | 270.4 × 202.8 mm, close to A4 (Waveshare listing) |
| Colors | Spectra 6: black, white, red, yellow, blue, green | Same |
| Full refresh | About 30 s on our build | About 25–27 s on our build; Waveshare lists 19 s |
| Frame size | 192,000 bytes at 4 bpp; our firmware stores 384 KB per frame | 960,000 bytes at 4 bpp |
| Cached images in 16 MB flash (our firmware) | Up to 24 | About 10 |
| Controller | ESP32-S3; Good Display's ESP32E6-E01 board takes the panel directly | ESP32-S3 with PSRAM; two panel controllers, so two chip selects |
| Panel price (published) | Waveshare 7.3″ HAT (E) $57.99–$77.99, per our kit comparison | Waveshare 13.3″ $249.99–$259.99 |
| Best for | Door and desk signs, shelf-edge and endcap signs, labels, menus at the counter | Timetables, floor plans, posters, notice boards, wayfinding |
Resolution and PPI for both sizes are from Electromaker’s guide to Pimoroni’s Inky Impression; the 13.3-inch active area, refresh time and price are from Waveshare’s 13.3-inch Spectra 6 listing; the 7.3-inch price is from our Spectra 6 dev kit comparison. Prices are list prices for single panels and change often.
Start with what the sign has to say
Size follows content, not the other way round. Write the busiest version of the sign first, at the type size it needs to be read from where people actually stand, and see which panel it fits.
Where 7.3 inches is enough
- Meeting room and office door signs: room name, status and the next two or three bookings.
- Shelf-edge, endcap and counter signs: one offer, a price and a product image.
- Labels for bins, racks and kanban cards, read at arm's length.
- Desk and reception signs, menus at the till, hours on a door.
At about 16 by 10 centimetres, a 7.3-inch panel holds a headline, a few lines of detail and a small image. It is also the cheaper and simpler build: the panel plugs straight into an ESP32-S3 driver board, the frame fits in memory without PSRAM if you stream it, and our firmware caches up to 24 images so a sign keeps rotating content when Wi-Fi is down.
Where you need 13.3 inches
- A full day or week of classes, sessions or shifts on one board.
- Floor plans and wayfinding with colored zones.
- Posters and notices that would otherwise be printed at A4.
- Signs read from further back: a corridor wall, a studio entrance, a lobby.
The 13.3-inch panel is close to an A4 sheet and has about five times the pixels of the 7.3-inch, at a slightly higher density. That is what Advantech uses for classroom timetables at National Taipei University: a 13.3-inch color e-paper sign showing course schedules, attendance barcodes and notices. Electromaker suggests the larger size for noticeboards, menus, shared dashboards and reception areas.
What changes in the engineering
Memory and storage
Spectra 6 has six colors, so a pixel fits in 4 bits. An 800 × 480 frame is 192,000 bytes at that packing; a 1200 × 1600 frame is 960,000 bytes, more than the ESP32-S3’s internal SRAM. Our 13.3-inch build keeps its framebuffer in PSRAM. In flash, our 16 MB layout leaves about 9.9 MB for cached images: up to 24 frames on the 7.3-inch (stored at 384 KB each) and about ten on the 13.3-inch. Our ESP32-S3 vs ESP32-C6 comparison walks through the framebuffer math chip by chip.
Refresh time
Bigger does not mean slower. Our 13.3-inch driver logs a refresh of about 25 to 27 seconds, and our 7.3-inch about 30. Published numbers differ by panel revision: Waveshare lists 19 seconds for its 13.3-inch panel, while Electromaker reports that 7.3-inch Inky Impression units made from April 2026 use a new AC waveform panel with a 28-second core refresh. For either size, schedule changes for when nobody is watching, and decide whether to pre-clear; our ghosting checklist covers that trade-off.
Battery and network
The panel draws power only while it changes, and on most cadences the Wi-Fi wake dominates the energy budget. The difference with a larger panel is the download: each changed image is 960 KB instead of 384 KB on our builds, so the radio stays on longer for every new image. Unchanged images are not downloaded again, because the sign sends the content tags it already holds. Our battery life guide has the per-wake math.
Board and power
The 13.3-inch panel has two controllers, each driving half the screen, so it needs two chip selects and more GPIO. The driver board we build on uses an IP5306 power-bank chip that has to be configured at every boot, or it can cut power when the load gets light. Neither is hard once known, but it is more bring-up work than the 7.3-inch, which is worth budgeting if you are moving from a dev kit to a product.
Cost beyond the panel
- Panel: the 13.3-inch costs three to four times the 7.3-inch at published single-unit list prices.
- Enclosure and mounting: a near-A4 front needs a stiffer frame and a wall fixing rated for it.
- Spares: budget spare panels into a rollout; a broken 13.3-inch panel is the more expensive one to replace.
- Content: more pixels means more layout work per template, not just bigger type.
For a full breakdown of what goes into a deployed sign, see how much e-paper signage costs. If you need bigger than 13.3 inches, our 32-inch e-paper comparison covers the large-format options.
Mixing sizes in one fleet
Most deployments end up with both: 7.3-inch signs on doors and shelves, a 13.3-inch board at the entrance. Because our firmware and cloud serve both panels, each device reports its panel model and the server bakes images at the right size and orientation, so one content system runs the whole fleet. Our workplace signage use case shows that split for offices, and the retail shelves use case for stores.
Spectra 6: E Ink’s six-pigment color e-paper film (black, white, red, yellow, blue and green), used in panels from 4 inches up to 32 inches. Panels of different sizes share the film but differ in resolution, controller and driver.
FAQ
What is the difference between 7.3-inch and 13.3-inch Spectra 6 e-paper?
Both use the same six-color E Ink Spectra 6 film. The 7.3-inch panel is 800 × 480 pixels (about 127 PPI, 5:3); the 13.3-inch is 1600 × 1200 (about 150 PPI, 4:3), close to A4 and roughly five times the pixels. The larger panel needs more memory, downloads a bigger image on every change and costs more, but it can carry a full timetable, floor plan or poster where the 7.3-inch suits a door, shelf or desk.
Is a 13.3-inch e-paper display slower to refresh than a 7.3-inch?
Not necessarily. Published figures vary by panel revision and driver: Waveshare lists 19 seconds for its 13.3-inch Spectra 6 panel, and Electromaker reports a 28-second core refresh for 7.3-inch Inky Impression units made from April 2026. On our own builds both sizes take roughly 25 to 30 seconds. Plan for tens of seconds either way.
How much memory does a 13.3-inch color e-paper frame need?
At 4 bits per pixel, a 1600 × 1200 frame is 960,000 bytes, against 192,000 bytes for 800 × 480. That is more than an ESP32-S3's internal SRAM, so our 13.3-inch build holds the frame in PSRAM. Our 7.3-inch firmware stores frames at one byte per pixel, 384 KB each, and fits about 24 cached images in flash; the 13.3-inch fits about ten.
Does a bigger e-paper sign use more battery?
Somewhat. The panel only draws power while it refreshes, and for most cadences the Wi-Fi wake costs more than the panel. A larger panel does download a bigger file each time the image changes, 960 KB instead of 384 KB on our builds, so changed images keep the radio on longer. Unchanged images are not downloaded again.
Which size is better for a room sign?
7.3 inches for a door or corridor sign read from a step or two away: room name, status and the next few bookings. 13.3 inches when the sign must carry a full day's schedule, a floor plan or a poster, or be read from further back, such as a timetable board or wayfinding sign.