Writing · Checklist

How to fix ghosting on color e-paper signs: a field checklist

To fix ghosting on an e-paper sign, drive the whole panel to solid white with a full refresh before drawing the next image, either before every update or on a schedule. That clears the faint copy of the previous image in most cases, at the cost of a second full refresh: on our ESP32-S3 + Spectra 6 signs, about 30 seconds becomes about 60, with a white flash. If a trace survives several clear cycles, the cause is more likely temperature, a sagging supply during refresh, the waveform or the panel itself. Below is the checklist we work through, in order.

Published 2026-11-20. Written for teams running or building color e-paper signs, shelf labels and frames. We build on ESP32-S3 and E Ink Spectra 6 panels from Good Display (the 7.3-inch GDEP073E01 and 13.3-inch GDEP133C02), so the firmware details below are from our own code. Consumer e-readers have their own settings and are not covered here.

What ghosting is, and what it isn’t

An e-paper pixel is a small cell of charged pigment particles. A refresh applies a sequence of voltages, the waveform, that moves the right particles to the front. When some particles do not complete the trip, part of the old image stays visible under the new one. That faint copy is ghosting. TRMNL’s help center describes the cause as a charge imbalance on the display that leaves the particles a smaller range of movement.

Ghosting: A faint trace of the previous image that remains after an e-paper refresh, most visible where a dark or saturated area has become white or a light color.

Two things are often mistaken for it. Washed-out or shifted colors across the whole image are usually a waveform, temperature or image conversion problem; our Spectra 6 image preparation guide covers the conversion side. A half-drawn image, or one that stops partway, is usually power or a reset during refresh, which our brownout checklist covers.

The ghosting checklist

Work through it top to bottom; most signs are fixed by row three.

StepWhat to do or checkWhat it tells you
Confirm it is ghostingA faint copy of the previous image, strongest where saturated color became whiteFaded or washed-out colors across the whole image are a different problem: waveform, temperature or image conversion
Run one manual clearSolid white full refresh, then the image againIf the trace disappears, it was ordinary ghosting; if it survives three clears, go to the panel and power rows
Turn on a pre-clear or cleaning cycleWhite sweep before each image, or a scheduled cleaning cycleFixes most cases; costs one extra full refresh of time and battery each time it runs
Move updates out of viewSchedule refreshes before opening, between sessions or overnightThe white flash stops mattering when nobody is watching
Check temperature at the signCold entrances, docks, freezer areas, ventsParticles move slower in the cold; ghosting that tracks location is a temperature clue
Check the supply during refreshBattery voltage and resets while the panel is busyA sagging supply can cut a waveform short and leave a partial image
Review the contentLarge saturated blocks that alternate with whiteThe hardest transitions; a mid-tone or white background is more forgiving
Test a second panelSame image, same firmware, a panel from another lotIsolates a bad panel or a waveform that does not suit that lot

Fix 1: a white pre-clear before each image

The most reliable fix is to give the particles a clean start. Our firmware has a per-device pre_clear setting, off by default. When it is on, every update first writes an all-white frame and runs a full refresh, then streams the new image and refreshes again. The comment in our 7.3-inch driver sums up the trade: it “roughly doubles per-update wallclock (~30 s + ~30 s) and adds a clear white flash, but eliminates ghosting.” The 13.3-inch driver does the same, with the same doubling.

What the pre-clear costs

Our battery life guide has the per-wake math if you want to price the extra refresh for your cadence.

Fix 2: a scheduled cleaning cycle

If a white flash on every update is unacceptable, clean on a schedule instead. TRMNL ships this as a Screen Wiper playlist item that runs a sequence of charge cycles moving the particles between black and white. TRMNL says it may flash for 30–60 seconds, or up to five minutes depending on the model, suggests running it once a day or once a week, and suggests doing it just after the device’s sleep period ends. The same idea works on any fleet: one cleaning refresh at the first wake of the day, and ordinary single refreshes after that.

Fix 3: move updates to when nobody is looking

A clear cycle is only a problem if someone sees it. Most business signs know their content ahead of time: opening hours, menus, class timetables, shelf prices. Schedule the change for the minutes before opening or between sessions and the pre-clear becomes invisible. Our firmware can wake at up to 24 set times a day; our guide to waking an ESP32 at a specific time shows how that schedule works.

When the clear cycle does not fix it

Temperature

Particles move more slowly in the cold, which is why e-paper controllers use temperature-dependent waveforms. TRMNL’s help center recommends trying its temperature profiles before the Screen Wiper. If ghosting appears only on signs in cold entrances, loading docks or near air-conditioning vents, log the temperature at the sign before touching the firmware.

Power during refresh

The refresh is the biggest current draw a battery sign has. If the supply sags enough to reset the board or cut the waveform short, the result can look like a stubborn ghost. On our 13.3-inch build the firmware polls the panel’s busy line during refresh and logs a timeout if the panel never reports ready, which is how we tell a power fault from a content one.

Waveform and panel lot

Panel makers keep improving waveforms. Electromaker, summarising Pimoroni, reports that 7.3-inch Inky Impression units made from April 2026 use a new AC waveform panel with a 28-second core refresh, in exchange for color improvements and reduced ghosting. If two batches of the same sign ghost differently, compare panel lots and the waveform each one is driven with before changing your content.

Content

The hardest transition is a large block of saturated color, such as a red promo banner, followed by plain white. Designing templates with a white or light background, and keeping the big color blocks in the same place from one image to the next, gives the panel less to undo. Test the worst-case pair from your actual content calendar, not a photo.

Partial refresh

On black-and-white e-paper, fast and partial refresh modes are the usual source of ghosting, because they skip part of the driving that cleans the old image. Color Spectra 6 panels are normally refreshed in full; Waveshare lists a 19-second full refresh for its 13.3-inch Spectra 6 panel and no partial refresh. Our firmware always does a full refresh.

Make it a product setting

For a product team, the useful decision is who gets to choose. A gallery frame can pre-clear every time. A shelf sign that changes during opening hours probably should not. We expose the pre-clear as a setting per device, so the same hardware can serve both. Our dev kit to product checklist lists it alongside the other decisions to make before a pilot, and the hardware partner checklist includes the ghosting questions to ask a vendor.

FAQ

What causes ghosting on an e-paper display?

Ghosting is a faint trace of the previous image left behind after a refresh. The pigment particles in each cell do not all travel all the way to their new position, so some of the old image stays visible. TRMNL's help center describes it as a charge imbalance that narrows how far the particles can move. Short or mistuned waveforms, temperature and the kind of transition (saturated color to white is the hardest) all make it worse.

How do you get rid of ghosting on an e-paper sign?

Drive the whole panel to a solid color, usually white, with a full waveform, then draw the new image. On our ESP32-S3 + Spectra 6 firmware this is a per-device pre-clear setting. It removes the bleed-through but roughly doubles the update, from about 30 seconds to about 60, and adds a visible white flash. Devices that do not have a pre-clear can run a periodic cleaning cycle instead.

Is e-paper ghosting permanent?

Usually not. Ordinary ghosting clears after one or more full clear cycles. If a faint image survives several clear cycles, or appears only on part of the panel, suspect the panel, the waveform for that panel lot, or the supply voltage during refresh, and test a second panel before changing anything else.

Does a partial refresh cause more ghosting?

On black-and-white e-paper, yes: partial and fast refresh modes skip some of the driving that cleans the old image. Color Spectra 6 panels are normally driven with a full refresh only; Waveshare lists a full refresh time for its 13.3-inch Spectra 6 panel and no partial refresh. If you are on color e-paper and still see ghosting, the fix is a clear cycle, not a slower partial mode.

Should a business sign run a clear cycle before every update?

It depends on who is watching. A sign that updates before opening or overnight can afford the extra 30 seconds and the white flash on every update. A sign that changes while customers stand in front of it may be better with a clear cycle once a day or once a week. Make it a setting rather than a hard-coded choice.

Does ghosting get worse in the cold?

Temperature changes how fast the particles move, which is why panel drivers use temperature-dependent waveforms. TRMNL recommends trying its temperature profiles before running its Screen Wiper. If ghosting shows up only on signs in cold entrances, loading docks or near AC vents, treat it as a temperature problem first.